16-04-2012, 01:08 PM
Basic Electrial- Compiled
Basic Electrial- Compiled.doc (Size: 5.37 MB / Downloads: 56)
In this chapter you gain to understand the following:
Electrical domestic wiring
Types of wiring
• Suitability of a particular wiring system for a given installation
Corridor and staircase lighting
Necessity of earthing
• Different types of earthing
Fuses
• Different types of fuses
Working of a fluorescent lamp and sodium vapor lamp
Introduction
A network of wires drawn connecting the meter board to the various energy consuming loads (lamps, fans, motors etc) through control and protective devices for efficient distribution of power is known as electrical wiring.
Electrical wiring done in residential and commercial buildings to provide power for lights, fans, pumps and other domestic appliances is known as domestic wiring. There are several wiring systems in practice. They can be classified into:
Tree system - In this system branches are tapped from the main circuit at required points. This involves many joints making the location of the fault point difficult.
Though the method is economical it is visually unappealing with scattered fuses and is affected by large voltage drops.
Distribution system - This system is more organized in the sense that the main circuit is drawn to several distribution centers and connected to the distribution boards. Branches are tapped from these distribution boards. This system of wiring has an aesthetic appeal, as they are without joints and also makes the location of the fault point easier. All the points are maintained almost at the same potential. Each circuit is provided with an independent fuse. Provides flexibility for repair and maintenance. This system is widely preferred for indoor wiring though expensive.
Types of Wiring:
Cleat wiring
CTS wiring or TRS wiring or batten wiring
Metal sheathed wiring or lead sheathed wiring
Casing and capping
Conduit wiring
1. Cleat wiring:
In this type of wiring, insulated conductors (usually VIR, Vulcanized Indian Rubber) are supported on porcelain or wooden cleats. The cleats have two halves one base and the other cap. The cables are placed in the grooves provided in the base and then the cap is placed. Both are fixed securely on the walls by 40mm long screws. The cleats are easy to erect and are fixed 4.5 – 15 cms apart. This wiring is suitable for temporary installations where cost is the main criteria but not the appearance.
Advantages:
1. Easy installation
2. Materials can be retrieved for reuse
3. Flexibility provided for inspection, modifications and expansion.
4. Relatively economical
5. Skilled manpower not required.
Disadvantages:
1. Appearance is not good
2. Open system of wiring requiring regular cleaning.
3. Higher risk of mechanical injury.
2. CTS ( Cable Tyre Sheathed) / TRS ( Tough Rubber Sheathed )
/ Batten wiring:
In this wiring system, wires sheathed in tough rubber are used which are quite flexible. They are clipped on wooden battens with brass clips (link or joint) and fixed on to the walls or ceilings by flat head screws. These cables are moisture and chemical proof. They are suitable for damp climate but not suitable for outdoor use in sunlight. TRS wiring is suitable for lighting in low voltage installations
Advantages:
1. Easy installation and is durable
2. Lower risk of short circuit.
3. Cheaper than casing and capping system of wiring
4. Gives a good appearance if properly erected.
Disadvantages:
1. Danger of mechanical injury.
2. Danger of fire hazard.
3. Should not be exposed to direct sunlight.
4. Skilled workmen are required.
3. Metal Sheathed or Lead Sheathed wiring :
The wiring is similar to that of CTS but the conductors (two or three) are individually insulated and covered with a common outer lead-aluminum alloy sheath. The sheath protects the cable against dampness, atmospheric extremities and mechanical damages. The sheath is earthed at every junction to provide a path to ground for the leakage current. They are fixed by means of metal clips on wooden battens. The wiring system is very expensive. It is suitable for low voltage installations.
Precautions to be taken during installation
1. The clips used to fix the cables on battens should not react with the sheath.
2. Lead sheath should be properly earthed to prevent shocks due to leakage currents.
3. Cables should not be run in damp places and in areas where chemicals (may react with the lead) are used.
Advantages:
1. Easy installation and is aesthetic in appearance.
2. Highly durable
3. Suitable in adverse climatic conditions provided the joints are not exposed
Disadvantages:
1. Requires skilled labor
2. Very expensive
3. Unsuitable for chemical industries
4. Casing and Capping:
It consists of insulated conductors laid inside rectangular, teakwood or PVC boxes having grooves inside it. A rectangular strip of wood called capping having same width as that of casing is fixed over it. Both the casing and the capping are screwed together at every 15 cms. Casing is attached to the wall. Two or more wires of same polarity are drawn through different grooves. The system is suitable for indoor and domestic installations.
Advantages:
1. Cheaper than lead sheathed and conduit wiring.
2. Provides good isolation as the conductors are placed apart reducing the risk of short circuit.
3. Easily accessible for inspection and repairs.
4. Since the wires are not exposed to atmosphere, insulation is less affected by dust, dirt and climatic variations.
Disadvantages:
1. Highly inflammable.
2. Usage of unseasoned wood gets damaged by termites.
3. Skilled workmanship required.
5. Conduit wiring:
In this system PVC (polyvinyl chloride) or VIR cables are run through metallic or PVC pipes providing good protection against mechanical injury and fire due to short circuit. They are either embedded inside the walls or supported over the walls, and are known as concealed wiring or surface conduit wiring (open conduit) respectively. The conduits are buried inside the walls on wooden gutties and the wires are drawn through them with fish (steel) wires. The system is best suited for public buildings, industries and workshops.