13-02-2013, 09:52 AM
MICROCONTROLLER BASED ANESTHESIA INJECTOR
MICROCONTROLLER .ppt (Size: 326 KB / Downloads: 40)
NECCESITY OF MBAI
Major operations are performed to remove or reconstruct the infected parts in the human body. These operations will lead to blood loss and pain. Therefore it is necessary to arrest the pain and the blood loss. Anesthesia plays an important role in the part of painkilling .AAI can be defined as “Automatic administration of anesthesia based on the bio-medical parameters of the patient, eliminating future side effects and the need for an anesthetist.”
Anesthesia is very essential in performing painless surgery and so an Automatic administration of Anesthesia is needed for a successful surgery.
WORKING
By using the keypad provided along with the Microcontroller, the anesthetist can set the level of anesthesia to be administered to the patient in terms of milliliters per hour (1ml to 1000ml). After receiving the anesthesia level from the keypad, the Microcontroller sets the system to administer anesthesia to the prescribed level. It then analyses various bio-medical parameters obtained from the sensors to determine the direction of rotation of the stepper motor. The rotation of the stepper motor causes the Infusion Pump to move in forward or in a backward direction and the anesthesia provided in the syringe is injected into the body of the patient. If the level of anesthesia is decreased to lower level than the set value, the alarm gets activated to alert the anesthetist to refill the anesthesia in the syringe pump to continue the process. In this design, the total timing and opposite flow of blood will also be detected by using Micro Controller.
HEART BEAT SENSOR
Heart rate is our body's way of telling how hard it is going. It is very vital that heart beat has to be in normal while administering anesthesia to the patient. Normal heart beat is 72 beats per minute. A sensor is designed for monitoring the changes in the heart beat of the human body. There are 2 ways of monitoring heart rate information from the body. They are
Electrocardiogram (ECG)
PULSE
STEPPER MOTOR
A stepper motor transforms electrical pulses into equal increments of rotary shaft motion called steps
In Automatic Anesthesia Injector, a 4-phase stepper motor is used. Consider the four phases as S1, S2, S3 and S4. The switch sequence can be used to rotate the motor half steps of 0.9º clockwise or counter clockwise.
This clockwise and counter clockwise movement of the stepper motor is coordinated with the movement of the Syringe by means of a mechanical interface.
SYRINGE INFUSION PUMP
The Syringe Infusion pump provides uniform flow of fluid by precisely driving the plunger of a syringe towards its barrel. It provides accurate and continuous flow rate for precisely delivering anesthesia medication in critical medical care. It has an alarm system activated by Infra-Red Sensor and limit switches. The pump will stop automatically with an alarm when the syringe is empty or if any air-bubble enters the fluid line. Glass and plastic Syringes of all sizes from 1ml to 30ml can be used in the infusion pump. The flow rates can be adjusted from 1ml to 99ml/hr. Since it accepts other syringe size also, much lower flow rate can be obtained by using smaller syringes.
SOFTWARE DETAILS
A program is required which when burnt into the EPROM will operate with the AT 89C51 to do the function of monitoring the bio-medical parameters. The program answers the following requirements:
To read the input from the keypad provided with the microcontroller.
To activate the internal timer and enable it to interrupt the AT 89C51 whenever the timer overflows.
To read the parameters such as heart rate, respiration, body temperature once in every specified interval.
To check for the correctness of the parameter values and activate the alarm set with the system when the level of Anesthesia goes down.
To calculate the stepper motor movement (increase the speed or decrease the speed) with the parameters provided by the Sensors.
Continue the above until switched OFF or RESET.
EXPERIMENTAL RESULTS
The performance of the microcontroller was checked virtually by interfacing it with the computer. The program was written in the micro controller for analyzing the parameters. Then the microcontroller was interfaced with the PC using the Microsoft Communication Port interface in Visual Basic 6.0.
A Stepper motor designed in VB was made to run and the motor speed on various conditions was noted. When the respiration rate and the temperature were constant, the motor speed was found to be constant. When this parameter was varied (by manually coding the change in the microcontroller program), the stepper motor speed was also found to vary with the aid of the microcontroller.
CONCLUSION
Modern technologies have developed that promotes comfortable and better life which is disease free. PREVENTION IS BETTER THAN CURE and protection is intelligent than prevention and our presentation on MICROCONTROLLER BASED ANESTHESIA MACHINE is one of the efficient protecting systems.