05-11-2016, 11:25 AM
1465123161-36.optimumdesignanalysisofcompositedriveshaft.docx (Size: 1.88 MB / Downloads: 10)
Abstract:
Substituting composite structures for conventional metallic structures has many advantages because of higher specific stiffness and strength of composite materials. This work deals with the replacement of conventional two-piece steel drive shafts with a single-piece e-glass/ epoxy, high strength carbon/epoxy and high modulus carbon/epoxy composite drive shaft for an automotive application. The design parameters were optimized with the objective of minimizing the weight of composite drive shaft. The design optimization also showed significant potential improvement in the performance of drive shaft.
Introduction
The advanced composite materials such as Graphite, Carbon, Kevlar and Glass with suitable resins are widely used because of their high specific strength (strength/density) and high specific modulus (modulus/density). Advanced composite materials seem ideally suited for long, power driver shaft (propeller shaft) applications. Their elastic properties can be tailored to increase the torque they can carry as well as the rotational speed at which they operate. The drive shafts are used in automotive, aircraft and aerospace applications. The automotive industry is exploiting composite material technology for structural components construction in order to obtain the reduction of the weight without decrease in vehicle quality and reliability. It is known that energy conservation is one of the most important objectives in vehicle design and reduction of weight is one of the most effective measures to obtain this result. Actually, there is almost a direct proportionality between the weight of a vehicle and its fuel consumption, particularly in city driving.
2.1 Description of the Problem
Almost all automobiles (at least those which correspond to design with rear wheel drive and front engine installation) have transmission shafts. The weight reduction of the drive shaft can have a certain role in the general weight reduction of the vehicle and is a highly desirable goal, if it can be achieved without increase in cost and decrease in quality and reliability.
It is possible to achieve design of composite drive shaft with less weight to increase the first natural frequency of the shaft and to decrease the bending stresses using various stacking sequences. By doing the same, maximize the torque transmission and torsional buckling capabilities are also maximized.
2.2 Aim and Scope of the Work
This work deals with the replacement of a conventional steel drive shaft with E-Glass/ Epoxy, High Strength Carbon/Epoxy and High Modulus Carbon/Epoxy composite drive shafts for an automobile application.
9
2.3 Optimum Design Using Genetic Algorithm
The design parameters are to be optimized for E-Glass/ Epoxy, High Strength Carbon/Epoxy and High Modulus Carbon/Epoxy composite drive shafts of an automobile using Genetic Algorithm. The purpose of using Genetic Algorithm is to minimize the weight of the shaft, which is subjected to the constraints such as torque transmission, torsional buckling capacities and fundamental lateral natural frequency.
The design parameters to be optimized are,
Ply thickness
Number of plies required
Stacking sequence of Laminate
2.4 Analysis
1. Modelling of the High Strength Carbon/Epoxy composite drive shaft using ANSYS.
2. Static, Modal and Buckling analysis are to be carried out on the finite element model of the High Strength Carbon/Epoxy composite drive shaft using ANSYS.
3. To investigate
a) The stress and strain distributions in E-Glass/ Epoxy, High Strength Carbon/Epoxy and High Modulus Carbon/Epoxy composite drive shafts using classical lamination theory (CLT).
b) The effect of centrifugal forces on the torque transmission capacity of the composite drive shafts.
c) The effect of transverse shear and rotary inertia on the fundamental lateral natural frequency of the shaft.
Background
Composites consist of two or more materials or material phases that are combined to produce a material that has superior properties to those of its individual constituents. The constituents are combined at a macroscopic level and or not soluble in each other. The main difference between composite and an alloy are constituent materials which are insoluble in each other and the individual constituents retain those properties in the case of composites, where as in alloys, constituent materials are soluble in each other and forms a new material which has different properties from their constituents.
3.1 Classification of Composites
Composite materials can be classified as
Polymer matrix composites
Metal matrix composites
Ceramic Matrix
Technologically, the most important composites are those in which the dispersed phase is in the form of a fiber. The design of fiber-reinforced composites is based on the high strength and stiffness on a weight basis. Specific strength is the ratio between strength and density. Specific modulus is the ratio between modulus and density. Fiber length has a great influence on the mechanical characteristics of a material. The fibers can be either long or short. Long continuous fibers are easy to orient and process, while short fibers cannot be controlled fully for proper orientation. Long fibers provide many benefits over short fibers. These include impact resistance, low shrinkage, improved surface finish, and dimensional stability. However, short fibers provide low cost, are easy to work with, and have fast cycle time fabrication procedures. The characteristics of the fiber-reinforced composites depend not only on the properties of the fiber, but also on the degree to which an applied load is transmitted to the fibers by the matrix phase.
The principal fibers in commercial use are various types of glass, carbon, graphite and Kevlar. All these fibers can be incorporated into a matrix either in continuous lengths or in discontinuous lengths as shown in the Fig 3.1. The matrix material may be a plastic or rubber polymer, metal or
11
ceramic. Laminate is obtained by stacking a number of thin layers of fibers and matrix consolidating them to the desired thickness. Fiber orientation in each layer can be controlled to generate a wide range of physical and mechanical properties for the composite laminate.
Advantages of Fiber Reinforced Composites
The advantages of composites over the conventional materials are [1, 2] High strength to weight ratio
High stiffness to weight ratio High impact resistance Better fatigue resistance Improved corrosion resistance Good thermal conductivity
Low Coefficient of thermal expansion. As a result, composite structures may exhibit a better dimensional stability over a wide temperature range.
High damping capacity.
12
3.3 Limitations of composites
The limitations of composites are [1, 2],
Mechanical characterization of a composite structure is more complex than that of a metallic structure
The design of fiber reinforced structure is difficult compared to a metallic structure, mainly due to the difference in properties in directions
The fabrication cost of composites is high Rework and repairing are difficult
They do not have a high combination of strength and fracture toughness as compared to metals
They do not necessarily give higher performance in all properties used for material selection
3.4 Applications of Composites
The common applications of composites are extending day by day. Nowadays they are used in medical applications too. The other fields of applications are,
Automotive : Drive shafts, clutch plates, engine blocks, push rods, frames, Valve guides, automotive racing brakes, filament–wound fuel tanks, fiber Glass/Epoxy leaf springs for heavy trucks and trailers, rocker arm covers, suspension arms and bearings for steering system, bumpers, body panels and doors
Aircraft: Drive shafts, rudders, elevators, bearings, landing gear doors, panels and floorings of airplanes etc.
Space: payload bay doors, remote manipulator arm, high gain antenna, antenna ribs and struts etc.
Marine: Propeller vanes, fans & blowers, gear cases, valves &strainers, condenser shells.
Chemical Industries: Composite vessels for liquid natural gas for alternative fuel vehicle, racked bottles for fire service, mountain climbing, under ground storage tanks, ducts and stacks etc.
Electrical & Electronics: Structures for overhead transmission lines for railways, Power line insulators, Lighting poles, Fiber optics tensile members etc.
13
Sports Goods: Tennis rackets, Golf club shafts, Fishing rods, Bicycle framework, Hockey sticks, Surfboards, Helmets and others.
3.5 Purpose of the Drive Shaft (or Propeller shaft)
The torque that is produced from the engine and transmission must be transferred to the rear wheels to push the vehicle forward and reverse. The drive shaft must provide a smooth, uninterrupted flow of power to the axles. The drive shaft and differential are used to transfer this torque.
3.6 Functions of the Drive Shaft
1 First, it must transmit torque from the transmission to the differential gear box.
2 During the operation, it is necessary to transmit maximum low-gear torque developed by the engine.
3 The drive shafts must also be capable of rotating at the very fast speeds required by the vehicle.
4 The drive shaft must also operate through constantly changing angles between the transmission, the differential and the axles. As the rear wheels roll over bumps in the road, the differential and axles move up and down. This movement changes the angle between the transmission and the differential.
5 The length of the drive shaft must also be capable of changing while transmitting torque. Length changes are caused by axle movement due to torque reaction, road deflections, braking loads and so on. A slip joint is used to compensate for this motion. The slip joint is usually made of an internal and external spline. It is located on the front end of the drive shaft and is connected to the transmission.
3.7 Different Types of Shafts
1 Transmission shaft: These shafts transmit power between the
source and the machines absorbing power. The counter shafts, line shafts, overhead shafts and all factory shafts are transmission shafts. Since these shafts carry machine parts such as pulleys, gears etc., therefore they are subjected to bending moments in addition to
14
twisting.
2 Machine Shaft: These shafts form an integral part of the machine itself. For example, the crankshaft is an integral part of I.C.engines slider-crank mechanism.
3 Axle: A shaft is called “an axle”, if it is a stationary machine
element and is used for the transmission of bending moment only. It simply acts as a support for rotating bodies.
Application: To support hoisting drum, a car wheel or a rope sheave.
4 Spindle: A shaft is called “a spindle”, if it is a short shaft that imparts motion either to a cutting tool or to a work-piece.
Applications:
1. Drill press spindles-impart motion to cutting tool (i.e.) drill.
2. Lathe spindles-impart motion to work-piece.
Apart from, an axle and a spindle, shafts are used at so many places and almost everywhere wherever power transmission is required. Few of them are:
1. Automobile Drive Shaft: Transmits power from main gearbox to differential gear box.
2. Ship Propeller Shaft: Transmits power from gearbox to propeller
attached on it.
3. Helicopter Tail Rotor Shaft: Transmits power to rail rotor fan.
This list has no end, since in every machine, gearboxes, automobiles etc. shafts are there to transmit power from one end to other.
Demerits of a Conventional Drive Shaft
1. They have less specific modulus and strength [3].
2. Increased weight [3].
3. Conventional steel drive shafts are usually manufactured in two pieces to increase the fundamental bending natural frequency because the bending natural frequency of a shaft is inversely proportional to the square of beam length and proportional to the square root of specific modulus. Therefore the steel drive shaft is made in two sections connected by a support structure, bearings and U-joints and hence over all weight of assembly will be more [4].
4. Its corrosion resistance is less as compared with composite materials [4].
5. Steel drive shafts have less damping capacity
3.11 Merits of Composite Drive Shaft
1 They have high specific modulus and strength.
2 Reduced weight.
3 The fundamental natural frequency of the carbon fiber composite drive shaft can be twice as high as that of steel or aluminium because the carbon fiber composite material has more than 4 times the specific stiffness of steel or aluminium, which makes it possible to manufacture the drive shaft of passenger cars in one piece. A one-piece composite shaft can be manufactured so as to satisfy the vibration requirements. This eliminates all the assembly, connecting the two piece steel shafts and thus minimizes the overall weight, vibrations and the total cost [4].
4 Due to the weight reduction, fuel consumption will be reduced [3].
5 They have high damping capacity hence they produce less vibration and noise [4].
6 They have good corrosion resistance [3].
7 Greater torque capacity than steel or aluminium shaft [5].
8 Longer fatigue life than steel or aluminium shaft [5].
9 Lower rotating weight transmits more of available power [5].
17
3.12 Drive Shaft Vibration
Vibration is the most common drive shaft problem. Small cars and short vans and trucks (LMV) are able to use a single drive shaft with a slip joint at the front end without experiencing any undue vibration. However, with vehicles of longer wheel base, the longer drive shaft required would tend to sag and under certain operating conditions would tend to whirl and then setup resonant vibrations in the body of the vehicle, which will cause the body to vibrate as the shaft whirls.
Vibration can be either transverse or torsional. Transverse vibration is the result of unbalanced condition acting on the shaft. This condition is usually by dirt or foreign material on the shaft, and it can cause a rather noticeable vibration in the vehicle. Torsional vibration occurs from the power impulses of the engine or from improper universal join angles. It causes a noticeable sound disturbance and can cause a mechanical shaking. In excess, both types of vibration can cause damage to the universal joints and bearings. Whirling of a rotating shaft happens when the centre of gravity of the shaft mass is eccentric and so is acted upon by a centrifugal force which tends to bend or bow the shaft so that it orbits about the shaft longitudinal axis like a rotating skipping rope. As the speed rises, the eccentric deflection of the shaft increases, with the result that the centrifugal force also will increase. The effect is therefore cumulative and will continue until the whirling become critical, at which point the shaft will vibrate violently.
From the theory of whirling, it has been found that the critical whirling speed of the shaft is inversely proportional to the square of the shaft length. If, therefore, a shaft having, for example, a critical whirling speed of 6000 rev/min is doubled in length, the critical whirling of the new shaft will be reduced to a quarter of this, i.e. the shaft will now begin to rotate at 1500 rev/min. The vibration problem could solve by increasing the diameter of the shaft, but this would increase its strength beyond its torque carrying requirements and at the same time increase its inertia, which would oppose the vehicle’s acceleration and deceleration. Another alternative solution frequently adopted by car, van, and commercial vehicle manufacturers is the use of two-piece drive shafts supported by intermediate or centre bearings. But this will increase the cost considerably.
18
4. Literature Survey
4.1 Composites
The theoretical details of composite materials and composite structures are extensively reviewed [6]. The Spicer U-Joint Division of Dana Corporation for the Ford Econoline van models developed the first composite propeller shaft in 1985. The General Motors pickup trucks, which adopted the Spicer product, enjoyed a demand three times that of projected sales in its first year [4, 5]. John. W. Weeton et al. [7] briefly described the application possibilities of composites in the field of automotive industry to manufacture composite elliptic springs, drive shafts and leaf springs. Beard more and Johnson [8] discussed the potential for composites in structural automotive applications from a structural point of view. Pollard [9] studied the possibility of the polymer Matrix composites usage in driveline applications. Faust et.al, [10] described the considerable interest on the part of both the helicopter and automobile industries in the development of lightweight drive shafts.
Procedure for finding the elastic moduli of anisotropic laminated composites is explained by Azzi.V.D et.al, [11]. Azzi.V.D .et.al, discussed about anisotropic strength of composites [12].
4.2 Torsional Buckling
The problem of general instability under torsional load has been studied by many investigators. Greenhill [13] obtained a solution for the torsional stability of a long shaft. The first analysis of buckling of thin-walled tubes under torsion made by Schwerin [14], but his analysis did not agree with his experimental data. However, all these papers were limited to isotropic materials.
As far as orthotropic materials are concerned, general theories of orthotropic shells were developed by Ambartsumyan [15] and Dong et al. [16]. Cheng and Ho [17] analyzed more generally, the buckling problems of non-homogeneous anisotropic cylindrical shells under combined axial, radial and torsional loads with all four boundary conditions at each end of the cylinder. Lien-Wen Chen et.al. [18] analyzed the stability behaviour of rotating composite shafts under axial compressive loads. A theoretical
19
analysis was presented for determining the buckling torque of a cylindrical hollow shaft with layers of arbitrarily laminated composite materials by means of various thin-shell theories [19]. Bauchau et al., [20] measured the torsional buckling loads of graphite/epoxy shafts, which were in good agreement with theoretical predictions based on a general shell theory including elastic coupling effects and transverse shearing deformations.
4.3 Lateral Vibrations
Bauchau [21] developed procedure for optimum design of high-speed composite drive shaft made of laminates to increase the first natural frequency of the shaft and to decrease the bending stress. Shell theory based on the critical speed analyses of drive shafts has been presented by Dos Reis et al. [22]. Patricia L.Hetherington [23] investigated the dynamic behaviour of supercritical composite drive shafts for helicopter applications. Ganapathi.et.al [24] extensively studied the nonlinear free flexural vibrations of laminated circular cylindrical shells. A method of analysis involving Love’s first approximation theory and Ritz’s procedure is used to study the influence of boundary conditions and fiber orientation on the natural frequencies of thin orthotropic laminated cylindrical shells was presented [25].A first order theory was presented by Lee[26] to determine the natural frequencies of an orthotropic shell. Nowinski. J.L. [27] investigated the nonlinear transverse vibrations of elastic orthotropic shells using Von-Karman-Tsien equations.
4.4 Optimization
The optimum design of laminated plates and shells subjected to constraints on strength, stiffness, buckling loads, and fundamental natural frequencies were examined [28]. Methods were proposed for the determination of the optimal ply angle variation through the thickness of symmetric angle-ply shells of uniform thickness [29]. The main features of GAs and several ways in which they can solve difficult design problems were discussed by Gabor Renner et.al.[30]. Raphael T.Haftka [31] discussed extensively about stacking-sequence optimization for buckling of laminated plates by integer programming. The use of a GA to optimize the stacking sequence of
20
composite laminates for buckling load maximization was studied. Various genetic parameters including the population size, the probability of mutation, and the probability of crossover were optimized by numerical experiments [32]. The use of GAs for the optimal design of symmetric composite laminates subject to various loading and boundary conditions were explained [33]. Kim, et.al. [34] minimized the weight of composite laminates with ply drop under a strength constraint. The working of Simple Genetic Algorithm was explained by Goldberg [35]. Rajeev and Krishnamoorthy [36] proposed a method for converting a constrained optimization problem into an unconstrained optimization problem.