06-12-2012, 05:33 PM
SOLARDISTILLWATER–ASAFEEDSTOCKTO INDUSTRIALBOILERS
SOLARDISTILLWATER.docx (Size: 1.66 MB / Downloads: 32)
ABSTRACT:-
There is an important need for clean, pure drinking water in many developing countries. Often water sources are brackish (i.e. contain dissolved salts) and/or contain harmful bacteria and therefore cannot be used for drinking. In addition, there are many coastal locations where seawater is abundant but potable water is not available. Pure water is also useful for batteries and in hospitals or schools.
Distillation is one of many processes that can be used for water purification. This requires an energy input, as heat, solar radiation can be the source of energy. In this process, water is evaporated, thus separating water vapour from dissolved matter, which is condensed as pure water. For people concerned about the quality of their municipally-supplied drinking water and
unhappy with other methods of additional purification available to them, solar distillation of
tap water or brackish groundwater can be a pleasant, energy-efficient option.This water can be used for many purposes.one of it’s industrial application is,”“Distilled water is used as a feed stock for Industrial Boilers.
SOLAR DISTILLATION
Introduction
There is an important need for clean, pure drinking water in many developing countries. Often water sources are brackish (i.e. contain dissolved salts) and/or contain harmful bacteria and therefore cannot be used for drinking. In addition, there are many coastal locations where seawater is abundant but potable water is not available. Pure water is also useful for batteries and in hospitals or schools.
Distillation is one of many processes that can be used for water purification. This requires an energy input, as heat, solar radiation can be the source of energy. In this process, water is evaporated, thus separating water vapour from dissolved matter, which is condensed as pure water.
Solar water distillation is a solar technology with a very long history and installations were built over 2000 years ago, although to produce salt rather than drinking water. Documented use of solar stills began in the sixteenth century. An early large-scale solar still was built in 1872 to supply a mining community in Chile with drinking water. Mass production occurred for the first time during the Second World War when 200,000 inflatable plastic stills were made to be kept in life-crafts for the US Navy.
There are a number of other approaches to water purification and desalination, such as photovoltaic powered reverse-osmosis, for which small-scale commercially available equipment is available. These are not considered here.
In addition, if treatment of polluted water is required rather than desalination, slow sand filtration is a good option.
The purpose of this technical brief is to provide basic information and direct the reader to other, more detailed sources.
Energy requirements for water distillation
The energy required to evaporate water is the latent heat of vaporisation of water. This has a value of 2260 kilojoules per kilogram (kJ/kg). This means that to produce 1 litre (i.e. 1kg since the density of water is 1kg/litre) of pure water by distilling brackish water requires a heat input of 2260kJ. This does not allow for the efficiency of the heating method, which will be less than 100%, or for any recovery of latent heat that is rejected when the water vapour is condensed.
It should be noted that, although 2260kJ/kg is required to evaporate water, to pump a kg of water through 20m head requires only 0.2kJ/kg. Distillation is therefore normally considered only where there is no local source of fresh water that can be easily pumped or lifted.
How a simple solar still operates
Figure 1 shows a single-basin still. The main features of operation are the same for all solar stills. The incident solar radiation is transmitted through the glass cover and is absorbed as heat by a black surface in contact with the water to be distilled. The water is thus heated and gives off water vapour. The vapour condenses on the glass cover, which is at a lower temperature because it is in contact with the ambient air, and runs down into a gutter from where it is fed to a storage tank.
Solar distillation Practical Action 2
single-basin still
Design objectives for an efficient solar still
For high efficiency the solar still should maintain:
• a high feed (undistilled) water temperature
• a large temperature difference between feed water and condensing surface
• lowvapour leakage.
A high feed water temperature can be achieved if:
• a high proportion of incoming radiation is absorbed by the feed water as heat. Hence low absorption glazing and a good radiation absorbing surface are required
• heat losses from the floor and walls are kept low
• the water is shallow so there is not so much to heat.
A large temperature difference can be achieved if:
• the condensing surface absorbs little or none of the incoming radiation
• condensing water dissipates heat which must be removed rapidly from the condensing surface by, for example, a second flow of water or air, or by condensing at night.
General arrangement
Design types and their performance
Single-basin stills have been much studied and their behaviour is well understood. Efficiencies of 25% are typical. Daily output as a function of solar irradiation is greatest in the early evening when the feed water is still hot but when outside temperatures are falling.
Material selection is very important. The cover can be either glass or plastic. Glass is considered to be best for most long-term applications, whereas a plastic (such as polyethylene) can be used for short-term use.
Sand concrete or waterproofed concrete are considered best for the basin of a long-life still if it is to be manufactured on-site, but for factory-manufactured stills, prefabricated ferro-concrete is a suitable material.
Multiple-effect basin stills have two or more compartments. The condensing surface of the lower compartment is the floor of the upper compartment. The heat given off by the condensing vapour provides energy to vaporize the feed water above. Efficiency is therefore greater than for a single-basin still typically being 35% or more but the cost and complexity are correspondingly higher.
Solar distillation Practical Action 3
Wick stills - In a wick still, the feed water flows slowly through a porous, radiation-absorbing pad (the wick). Two advantages are claimed over basin stills. First, the wick can be tilted so that the feed water presents a better angle to the sun (reducing reflection and presenting a large effective area). Second, less feed water is in the still at any time and so the water is heated more quickly and to a higher temperature.
Simple wick stills are more efficient than basin stills and some designs are claimed to cost less than a basin still of the same output.
Emergency still - To provide emergency drinking water on land, a very simple still can be made. It makes use of the moisture in the earth. All that is required is a plastic cover, a bowl or bucket, and a pebble.
Hybrid designs - There are a number of ways in which solar stills can usefully be combined with another function of technology. Three examples are given:
• Rainwater collection. By adding an external gutter, the still cover can be used for rainwater collection to supplement the solar still output.
• Greenhouse-solar still. The roof of a greenhouse can be used as the cover of a still.
• Supplementary heating. Waste heat from an engine or the condenser of a refrigerator can be used as an additional energy input.