12-06-2014, 03:42 PM
Study and Fabrication of Compressed Air Engine
1370250507-S2120110108.pdf (Size: 297.4 KB / Downloads: 109)
ABSTRACT
As the world is hard pressed with the energy and fuel crises, compounded by pollution of all kinds, any
technologies that bring out the solutions to this problem is considered as a bounty. In one of such new
technologies, is the development of a new engine called as compressed air engine which does not require any of
the known fuels like diesel, petrol, CNG, LPG, hydrogen etc. this works using only compressed air. This replaces
all types of to-date known fuels and also permanently solves the problems of pollution as its exhaust is clean and
cool measured practically as low as 5ºC. A proto type, a horizontal, single cylinder low speed engine was
modified to run on compressed air. Since this engine runs only on high pressure compressed air, the exhaust of
which is undoubtedly only air, making it a zero pollution engine. No heat is generated because there is no
combustion of fuel, hence this engine needs no cooling system and it result in reduced cost, weight, volume and
vibration. Early cost analysis shows that it's very cost effective and the operational cost is ten times less than that
of petrol or diesel. Experimental analysis were carried out on this modified engine to find out its performance
characteristics like brake power, mechanical efficiency, overall efficiency, air to Air ratio, volumetric efficiency,
cost analysis etc. Though the efficiencies were low as the frictional forces were high for the proto designed
engine, however the concept can be applied on a professionally designed engine to improve its performance.
INTRODUCTION
F
OSSIL fuels (i.e., petroleum, diesel, natural gas
and coal) which meet most of the world's energy
demand today are being depleted rapidly. Also, their
combustion products are causing global problems,
such as the green house effect, ozone layer depletion
acid rains and pollution which are posing great danger
for environment and eventually for the total life on
planet. These factors are leading automobile
manufactures to develop cars fueled by alternatives
energies. Hybrid cars, Fuel cell powered cars,
Hydrogen fueled cars will be soon in the market as a
result of it. One possible alternative is the air powered
car. Air, which is abundantly available and is free from
pollution, can be compressed to higher pressure at a
very low cost, is one of the prime option since
atmospheric pollution can be permanently eradicated.
Whereas so far all the attempts made to eliminate the
pollution has however to reduce it, but complete eradication is still rigorously pursued[1]. Compressed
air utilization in the pneumatic application has been
long proven. Air motors, pneumatic actuators and
others various such pneumatic equipments are in use.
Compressed air was also used in some of vehicle for
boosting the initial torque. Turbo charging has become
one of the popular techniques to enhance power and
improve the efficiencies of the automotive engine that
completely runs on compressed air. There are at two
ongoing projects (in France, by MDI and in S. Korea)
that are developing a new type of car that will run
only on compressed air. Similar attempt has been made
but to modify the existing engine and to test on
compressed air
COMPRESSED AIR
Compressed air is a gas, or a combination of
gases, that has been put under greater pressure than
the air in the general environment. Current applications
using compressed air are numerous and diverse, including jackhammers, tire pumps, air rifles, and
aerosol cheese. According to proponents,compressed
air also has a great deal of potential as a clean,
inexpensive, and infinitely renewable energy source.
Its use is currently being explored as an alternative to
fossil fuels
Behavior of compressed air
Compressed air is clean, safe, simple and efficient.
There are no dangerous exhaust fumes of or other
harmful by products when compressed air is used as
a utility. It is a non-combustible, non-polluting utility
When air at atmospheric pressure is mechanically
compressed by a compressor, the transformation
of air at 1 bar (atmospheric pressure) into air at higher
pressure (up to 414 bar) is determined by the laws
of thermodynamics. They state that an increase
in pressure equals a rise in heat and compressing air
creates a proportional increase in heat. Boyle's
law explains that if a volume of a gas (air) halves
during compression, then the pressure is doubled.
Charles' law states that the volume of a gas changes
in direct proportion to the temperature[2]. These laws
explain that pressure, volume and temperature are
proportional; change one variable and one or two of
the others will also change, according to this equation
Compressed air is normally used in pressure
ranges from 1 bar to 414 bar (14 to 6004 PSI) at
various flow rates from as little as 0.1 m (3.5 CFM -
cubic feet per minute) and up
How compressed air fuel a car
The laws of physics dictate that uncontained gases
will fill any given space. The easiest way to see this in
action is to inflate a balloon. The elastic skin of the
balloon holds the air tightly inside, but the moment
you use a pin to create a hole in the balloon's surface,
the air expands outward with so much energy that the
balloon explodes. Compressing a gas into a small
space is a way to store energy. When the gas expands
again, that energy is released to do work. That's the
basic principle behind what makes an air cargo[3].
The first air cars will have air compressors built
into them. After a brisk drive, you'll be able to take
the car home, put it into the garage and plug in the
compressor. The compressor will use air from around
the car to refill the compressed air tank. Unfortunately
this is a rather slow method of refueling and will
probably take up to two hours for a complete refill. If
the idea of an air car catches on, air refueling stations
will become available at ordinary gas stations, where
the tank can be refilled much more rapidly with air
that's already been compressed. Filling your tank at
the pump will probably take about three minutes
The first air cars will almost certainly use the
Compressed Air Engine (CAE) developed by the
French company, Motor Development International
(MDI). Air cars using this engine will have tanks that
will probably hold about 3,200 cubic feet (90.6
kiloliters) of compressed air. The vehicle's accelerator
operates a valve on its tank that allows air to be
released into a pipe and then into the engine, where
the pressure of the air's expansion will push against
the pistons and turn the crankshaft. This will produce
enough power for speeds of about 35 miles (56
kilometers) per hour. When the air car surpasses that
speed, a motor will kick in to operate the in-car air
compressor so it can compress more air on the fly
and provide extra power to the engine. The air is also
heated as it hits the engine, increasing its volume to
allow the car to move faster
CONSTRUCTION OF COMPRESSED
AIR ENGINE
The construction of compressed air engine mainly
consist of pneumatic cylinder, pneumatic solenoid
valve and working, light chaser circuit, compressor,
bearing & its working, and crank shaft[4]
Pneumatic cylinder
Pneumatic cylinders are mechanical devices
which produce force, often in combination with
movement,and are powered by compressed gas.
To perform their function, pneumatic cylinders
impart a force by converting the potential energy of
compressed gas into kinetic energy. This is achieved
by the compressed gas being able to expand, without
external energy input, which itself occurs due to the
pressure gradient established by the compressed gas
being at a greater pressure than the atmospheric
pressure. This air expansion forces a piston to move
in the desired direction[5].
Once actuated, compressed air enters into the tube
at one end of the piston and, hence, imparts force on
the piston. Consequently, the piston becomes displaced by the compressed air expanding in an
attempt to reach atmospheric pressure
Pneumatic solenoid valve and working
The term solenoid usually refers to a coil used to
create magnetic fields when wrapped around a
magnetic object or core. In engineering terms, the
solenoid describes transducer mechanisms used to
convert energy into motion. Solenoid valves are
controlled by the action of the solenoid and typically
control the flow of water or air as a switch. If the solenoid is active (current is applied), it opens the
valve. If the solenoid is inactive (current does not exist),
the valve stays closed. The action of the pneumatic
solenoid is controlled by the use of pneumatics. The
opening or closing of a valve is referred to as "changing
state."
An internally driven pilot valve with four-way
connections is generally found in pneumatic operations and is used to move double action
cylinders. Pneumatic solenoid valves can be
designed as stackable [6]
Light chaser circuit & its components
Light chaser circuits can be used to create lighting
animation sequences and have been used in the past
to attract attention for advertising and promotion,
such as the marquee at the local movie theater. In
addition, they can be used to produce pleasing effects
for entertainment as well [7].
Light chasers consist of several lighting circuits
strung together, usually three or four. Every first light
in the string is turned on, then off and the next light is
turned on and then off, and so on. Although there are
eight lights in the example below, there are only four
circuits controlling these lights, which are repeated
twice. The two lights that are on at any given time are
connected to the same circuit. In the Rainbow Kits
light chaser, the four circuits can be repeated up to10
times, giving a string of 40 LEDs
Compressor
A gas compressor is a mechanical device that
increases the pressure of a gas by reducing its volume.
Compressors are similar to pumps: both increase
the pressure on a fluid and both can transport the
fluid through a pipe. As gases are compressible, the
compressor also reduces the volume of a gas. Liquids
are relatively incompressible, so the main action
of a pump is to pressurize and transport liquids [8].
Compressed air Piston range operates between
0.75 kW to 420 kW (1hp to 563 hp) producing
working pressure at 1.5 bar to 414 bar (21 to
6004psi).
Compressed air Vane compressors operate
between 1.1 kW to 75 kW (1.5 to 100hp), producing
working pressures of 7 to 8 and 10 bar (101 to
145psi).
Crank shaft
The crankshaft translates reciprocating linear piston
motion into rotation. To convert the reciprocating
motion into rotation, the crankshaft has "crank throws"
or "crankpins", additional bearing surfaces whose axis
is offset from that of the crank, to which the "big ends"
of the connecting rods from each cylinder attach.
It typically connects to a flywheel, to reduce the
pulsation characteristic of the four-stroke cycle, and
sometimes a tensional or vibration damper at the
opposite end, to reduce the torsion vibrations often
caused along the length of the crankshaft by the
cylinders farthest from the output end acting on the
torsion elasticity of the metal.
ADVANTAGES
Compressed-air vehicles are comparable in many
ways to electric vehicles, but use compressed air to
store the energy instead of batteries. Their potential
advantages over other vehicles include:
Much like electrical vehicles, air powered
vehicles would ultimately be powered through
the electrical grid. This makes it easier to focus
on reducing pollution from one source, as
opposed to the millions of vehicles on the road.
Transportation of the fuel would not be required
due to drawing power off the electrical grid.
This presents significant cost benefits. Pollution created during fuel transportation would be
eliminated.
Compressed air technology reduces the cost
of vehicle production by about 20%, because
there is no need to build a cooling system, fuel
tank, Ignition Systems or silencers.
Air, on its own, is non-flammable.
High torque for minimum volume.
The mechanical design of the engine is simple
and robust.
Low manufacture and maintenance costs as well
as easy maintenance.
Compressed-air tanks can be disposed of or
recycled with less pollution than batteries.
Compressed-air vehicles are unconstrained by
the degradation problems associated with
current battery systems
The tank may be able to be refilled more often
and in less time than batteries can be recharged,
with re-fueling rates comparable to liquid fuels.
Lighter vehicles would mean less abuse on
roads. Resulting in longer lasting roads.
The price of fueling air-powered vehicles will
be significantly cheaper than current fuels
. DESCRIPTION OF AIR ENGINE
A compressed-air vehicle is powered by an air
engine, using compressed air, which is stored in a tank.
Instead of mixing fuel with air and burning it in the
engine to drive pistons with hot expanding gases,
compressed air vehicles (CAV) use the expansion of
compressed air to drive their pistons. One
manufacturer claims to have designed an engine that
is 90 percent efficient[9].
Compressed air propulsion may also be
incorporated in hybrid systems, e.g., battery electric
propulsion and fuel tanks to recharge the batteries.
This kind of system is called hybrid-pneumatic electric
propulsion. Additionally, regenerative braking can also
be used in conjunction with this system
Working of Cycle & Engine
Because of the dwell provided by the special
connecting rod assembly, the diesel engine works on
constant volume cycle instead of constant pressure
cycle. During this constant volume, air is injected by
the injection system into the engine cylinder.
This engine works like a diesel engine. At the end of compression stroke, a very high pressure air at
room temperature is injected into the cylinder.
Injection of air by electro-mechanical injection system
is governed by the cam dwell during which the piston
also dwells. As the in cylinder hot and compressed
air mixes with the externally injected relatively cold
and compressed air, injected at relatively higher
pressure than the inside pressure, the mixture tries to
attain a common equilibrium temperature of this
mixture falls down, expansion takes place. The high
inside mixture pressure impart a very heavy blow on
the head of the piston, which is then set in motion and
the engine runs. No combustion takes place; it is the
expansive forces, which make engine run.
Schematic diagram
In this model input is connected with air
compressor. This compressor air transfer into two
pneumatic piston through 4-solenoid valve, solenoid
valve rotate crank shaft. Each solenoid valve gives
90 degree rotation to crank shaft.
The preliminary analysis based on the prototype
calculation shows that around three cubic meter of
air at a pressure more than 30bar can give a mileage
equivalent to one liter petrol is Rs 52, and cost of
production of one cubic meter of air at a pressure of
50bar is Rs 3. Hence air of Rs 9 can give the mileage
of Rs 52 of petrol. However if air is mass compressed
and produced, the cost will further come down.
In this project a hermetically sealed reciprocating
second hand compressor from a domestic refrigerator
is being used in place of air compressor in reference
RESULTS AND DISCUSSION
The values noted down are used for calculating
the mechanical efficiency, indicated power brake
power; etc. Since this proto type was designed for
low speed, the output power; applied load was also
kept low. The prime aim being to test the concept of
application of air and the suitability of special
connecting rod assembly with its related advantages,
hence the obtain result may not be the exact measure
of its potential, since it wasn't very professionally
designed.
Indicated power
It can be seen that the indicated power is increasing
for increase of load. As load is increased, the speed
falls down, to maintain it constant injection pressure
has to be increased. As the injection pressure has to
be increased, the indicated mean effective pressure
gets increased; hence the indicated power is increased.
Indicated power is calculated by plotting the P-V
diagram and calculating the area under the curve.
Initial suction pressure p1
known as pressure after
compression p2
of air in cylinder is also known
because the compression ratio is known and the p3
is
the injection pressure of air from cylinder which can
be recorded from the pressure gauge, and the exhaust
pressure p4
is also recorded so the p-v plot can be
easily drawn as four pressures are known.
Power is defined as the rate of doing work. In the
analysis of cycles the network is expressed in kJ/Kg
of air. This may be converted to power by multiplying
the mass flow rate of air through the engine in kg/ time[10]. Since, the network obtained from the p-v
diagram is the network produced in the cylinder as
measured by an indicator diagram, the power based
there on is termed indicated power (ip).
CONCLUSION
This is a revolutionary engine design which is eco
friendly, pollution free, but also very economical. This
redresses both the problems of fuel crises and
pollution. However excessive research is needed to
completely prove the technology for both its
commercial and technical viability
It can be seen that the indicated power is increasing
for increase of load. As load is increased, the speed
falls down, to maintain it constant injection pressure
has to be increased. As the injection pressure has to
be increased, the indicated mean effective pressure
gets increased; hence the indicated power is increased
upon the application of the load. Though the applied
load was small, however, the developed power was
in proportion to the applied load. As load was applied
the speed was reduced, to maintain it constant, the
inlet air pressure has to be increased. As shown
injection pressure is increased. In the present case
the speed was maintained constant as 600 rpm. As
the output speed was less the brake power was
significantly lower. The mechanical efficiency is
increasing with the increase of output power. At lower
output it was very low