17-12-2009, 07:53 PM
Hi, pls help for this project topic "Fault Detection and Protection of Induction Motors Using Sensors". If u have any material post it..
17-12-2009, 07:53 PM
Hi, pls help for this project topic "Fault Detection and Protection of Induction Motors Using Sensors". If u have any material post it..
18-12-2009, 01:52 AM
Abstract Induction motors can be protected using some components, such as timers, contactors, voltage, and current relays. This is the classical method and involves mechanical dynamic parts.Protection of an induction motor (IM) against problems,like overvoltage, overcurrent, overload, overtemperature, and undervoltage, is very important, because it is used widely in industry as an actuator.Computer based and PIC(programmable integrated circuit ) based techniques are available. The computer-based protection method requires an analog-to-digital conversion card, and the PIC-based protection method does not visualize the electrical parameters measured. New method using PLC In this method, all contactors, timers, relays, and the conversion card are eliminated. And the voltages, the currents, the speed, and the temperature values of the motor, and the problems occurred in the system, are monitored and warning messages are shown on the computer screen. The stator current monitoring method for incipient fault detection in induction machines is widely used for some time.It has advantages such as: -No additional, potentially unreliable, sensors are necessary, above those current sensors already used for motor protection; -Electrical faults, such as broken rotor bars, rotor unbalances, bearing faults and stator winding faults can be observed; and driven load conditions can be determined. A fault detection algorithm is available to be used in the condition monitoring of the squirrel-cage induction motors, very widely used in industry all around the world. THE MOTOR CURRENT SIGNATURE ANALYSIS This technique depends upon locating by spectrum analysis specific harmonic components in the line current produced of unique rotating flux components caused by faults such as broken rotor bars, air-gap eccentricity and shorted turns in stator windings, etc. The assumptions taken here are: -The speed of the machine is constant and known. - The stator fundamental frequency is constant. -The load is constant. -The machine is sufficiently loaded in order to separate the sidebands from the fundamental. induction motor protection.pdf (Size: 208.41 KB / Downloads: 150) The exact IEEE paper on the subject can be referred at this link: http://ieeexplore.ieeexpl/freeabs_all.js...er=4603060 You have to have an IEEE membership or your institution must have a subscription to the IEEE Xplore digital library. Or try getting from friends. |
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
Request for project tittle | Guest | 2 | 287 |
05-04-2022, 04:57 PM Last Post: Arunprakash01 |
|
project request | Guest | 1 | 1,294 |
06-01-2018, 04:18 PM Last Post: dhanabhagya |
|
mini project request | Guest | 1 | 1,273 |
06-01-2018, 04:14 PM Last Post: dhanabhagya |
|
mechanical, automobile project | Guest | 1 | 1,311 |
17-11-2017, 12:28 PM Last Post: jaseela123 |
|
request for beam engine project construction details | Guest | 1 | 968 |
07-10-2017, 11:50 AM Last Post: jaseela123 |
|
MATLAB Prj help needed. | Guest | 1 | 938 |
07-10-2017, 10:04 AM Last Post: jaseela123 |
|
Power system protection project | Guest | 1 | 867 |
03-10-2017, 10:33 AM Last Post: jaseela123 |
|
send me the group fund queue project | Guest | 0 | 652 |
30-09-2017, 10:18 AM Last Post: Guest |
|
help regarding preparation of project work | Guest | 0 | 521 |
30-09-2017, 10:18 AM Last Post: Guest |
|
give a project on tap water alarm | Guest | 1 | 769 |
21-09-2017, 04:00 PM Last Post: jaseela123 |