26-08-2014, 02:59 PM
Wireless Charging Of Mobile Phones Using Microwaves Seminar Report
[attachment=67065]
Abstract
It is a hectic task to carry everywhere the charger of mobile phones or any electronic gadget while travelling
or it is very cruel when your mobile phone getting off by the time you urgently need it. It is the major problem in today’s
electronic gadgets. Though the world is leading with the developments in technology, but this technology is still incomplete
because of certain limitations. Today’s world requires the complete technology and for this purpose we are proposing
‘Wireless Charging of Mobile Phones Using Microwaves
INTRODUCTION
Microwaves are radio waves (a form of electromagnetic radiation) with wavelengths ranging from as long as one
meter to as short as one millimeter. The prefix "micro-" in "microwave" is not meant to suggest a wavelength in the
micrometer range. It indicates that microwaves are "small" compared to waves used in typical radio broadcasting,
in that they have shorter wavelengths.Microwave technology is extensively used for point-to-point telecommunications (i.e., non-broadcast uses).
Microwaves are especially suitable for this use since they are more easily focused into narrow beams than radio
waves, allowing frequency reuse; their comparatively higher frequencies allow broad bandwidth and high data
transmission rates, and antenna sizes are smaller than at lower frequencies because antenna size is inversely
proportional to transmitted frequency. Microwaves are used in spacecraft communication, and much of the world's
data, TV, and telephone communications are transmitted long distances by microwaves between ground stations
and communications satellites. Microwaves are also employed in microwave ovens and in radar technology.
With mobile phones becoming a basic part of life, the recharging of mobile phone batteries has always been a
problem. The mobile phones vary in their talk time and battery standby according to their manufacturer and
batteries. All these phones irrespective of their manufacturer and batteries have to be put to recharge after the
battery has drained out. The main objective of this current proposal is to make the recharging of the mobile phones
independent of their manufacturer and battery make. In this paper a new proposal has been made so as to make the
recharging of the mobile phones is done automatically as you talk in your mobile phone! This is done by use of
microwaves. The microwave signal is transmitted from the transmitter along with the message signal using special
kind of antennas called slotted wave guide antenna at a frequency is 2.45 GHz.
FUNCTIONING
The basic addition to the mobile phone is going to be the rectenna. A rectenna is a rectifying antenna, a special type
of antenna that is used to directly convert microwave energy into DC electricity. Its elements are usually arrangedin a mesh pattern, giving it a distinct appearance from most antennae. A simple rectenna can be constructed from a
Schottky diode placed between antenna dipoles. The diode rectifies the current induced in the antenna by the
microwaves. Rectenna are highly efficient at converting microwave energy to electricity. In laboratory
environments, efficiencies above 90% have been observed with regularity. Some experimentation has been done
with inverse rectenna, converting electricity into microwave energy, but efficiencies are much lower--only in the
area of 1%. With the advent of nanotechnology and MEMS the size of these devices can be brought down to
molecular level. A rectenna comprises of a mesh of dipoles and diodes for absorbing microwave energy from a
transmitter and converting it into electric power. Its elements are usually arranged in a mesh pattern, giving it a
distinct appearance from most antennae. A simple rectenna can be constructed from a Schottky diode placed
between antenna dipoles as shown in Fig... The diode rectifies the current induced in the antenna by the
microwaves. Rectenna are highly efficient at converting microwave energy to electricity.
LIMITATIONS
The Mobile Handset should additionally have a device, “Rectenna” which would make it bulky and hence device
size up to molecular level is essential. The main disadvantages of wireless charging are its lower efficiency and
increased resistive heating in comparison to direct contact. Implementations using lower frequencies or older drive
Technologies charge more slowly and generate heat within most portable electronics. Due to the lower efficiency,
devices can take longer to charge when supplied power is equal
INDUCTIVE CHARGING
Though some Handsets on the market currently provide wireless charging, the technology is not exactly same as
mentioned here. For charging, phones are required to keep near the Charging Plate. It uses inductively coupled
Power Transfer System.A transmitter coil is positioned at the bottom (L1) and the receiver coil (L2) is situated at the top and these coils are
embedded into different electrical devices. L1 would be the Nokia Wireless Charging Plate and L2 would be the
Nokia Lumia 920, for example. In coming days, Microwave might fix various issues in the current system.
CONCLUSION
In this modern era of Science and Technology, we do not have enough time to be constantly at one place and
recharge our Mobile Phones, Laptops etc. Regardless of office, we work even when we are at home, then our
Communicating media need sudden recharge without being interrupted. A novel use of the Rectenna and a sensor
in a Mobile phone could provide a new dimension in the revolution of Mobile Phone. Covering these aspects, this
new system of wireless recharging will certainly bring innovative Change in recharging Electronic Equipment and
will upgrade our Lifestyle. Thus this paper successfully demonstrates a novel method of using the microwave’s
power to charge the Mobile Phones.
[attachment=67065]
Abstract
It is a hectic task to carry everywhere the charger of mobile phones or any electronic gadget while travelling
or it is very cruel when your mobile phone getting off by the time you urgently need it. It is the major problem in today’s
electronic gadgets. Though the world is leading with the developments in technology, but this technology is still incomplete
because of certain limitations. Today’s world requires the complete technology and for this purpose we are proposing
‘Wireless Charging of Mobile Phones Using Microwaves
INTRODUCTION
Microwaves are radio waves (a form of electromagnetic radiation) with wavelengths ranging from as long as one
meter to as short as one millimeter. The prefix "micro-" in "microwave" is not meant to suggest a wavelength in the
micrometer range. It indicates that microwaves are "small" compared to waves used in typical radio broadcasting,
in that they have shorter wavelengths.Microwave technology is extensively used for point-to-point telecommunications (i.e., non-broadcast uses).
Microwaves are especially suitable for this use since they are more easily focused into narrow beams than radio
waves, allowing frequency reuse; their comparatively higher frequencies allow broad bandwidth and high data
transmission rates, and antenna sizes are smaller than at lower frequencies because antenna size is inversely
proportional to transmitted frequency. Microwaves are used in spacecraft communication, and much of the world's
data, TV, and telephone communications are transmitted long distances by microwaves between ground stations
and communications satellites. Microwaves are also employed in microwave ovens and in radar technology.
With mobile phones becoming a basic part of life, the recharging of mobile phone batteries has always been a
problem. The mobile phones vary in their talk time and battery standby according to their manufacturer and
batteries. All these phones irrespective of their manufacturer and batteries have to be put to recharge after the
battery has drained out. The main objective of this current proposal is to make the recharging of the mobile phones
independent of their manufacturer and battery make. In this paper a new proposal has been made so as to make the
recharging of the mobile phones is done automatically as you talk in your mobile phone! This is done by use of
microwaves. The microwave signal is transmitted from the transmitter along with the message signal using special
kind of antennas called slotted wave guide antenna at a frequency is 2.45 GHz.
FUNCTIONING
The basic addition to the mobile phone is going to be the rectenna. A rectenna is a rectifying antenna, a special type
of antenna that is used to directly convert microwave energy into DC electricity. Its elements are usually arrangedin a mesh pattern, giving it a distinct appearance from most antennae. A simple rectenna can be constructed from a
Schottky diode placed between antenna dipoles. The diode rectifies the current induced in the antenna by the
microwaves. Rectenna are highly efficient at converting microwave energy to electricity. In laboratory
environments, efficiencies above 90% have been observed with regularity. Some experimentation has been done
with inverse rectenna, converting electricity into microwave energy, but efficiencies are much lower--only in the
area of 1%. With the advent of nanotechnology and MEMS the size of these devices can be brought down to
molecular level. A rectenna comprises of a mesh of dipoles and diodes for absorbing microwave energy from a
transmitter and converting it into electric power. Its elements are usually arranged in a mesh pattern, giving it a
distinct appearance from most antennae. A simple rectenna can be constructed from a Schottky diode placed
between antenna dipoles as shown in Fig... The diode rectifies the current induced in the antenna by the
microwaves. Rectenna are highly efficient at converting microwave energy to electricity.
LIMITATIONS
The Mobile Handset should additionally have a device, “Rectenna” which would make it bulky and hence device
size up to molecular level is essential. The main disadvantages of wireless charging are its lower efficiency and
increased resistive heating in comparison to direct contact. Implementations using lower frequencies or older drive
Technologies charge more slowly and generate heat within most portable electronics. Due to the lower efficiency,
devices can take longer to charge when supplied power is equal
INDUCTIVE CHARGING
Though some Handsets on the market currently provide wireless charging, the technology is not exactly same as
mentioned here. For charging, phones are required to keep near the Charging Plate. It uses inductively coupled
Power Transfer System.A transmitter coil is positioned at the bottom (L1) and the receiver coil (L2) is situated at the top and these coils are
embedded into different electrical devices. L1 would be the Nokia Wireless Charging Plate and L2 would be the
Nokia Lumia 920, for example. In coming days, Microwave might fix various issues in the current system.
CONCLUSION
In this modern era of Science and Technology, we do not have enough time to be constantly at one place and
recharge our Mobile Phones, Laptops etc. Regardless of office, we work even when we are at home, then our
Communicating media need sudden recharge without being interrupted. A novel use of the Rectenna and a sensor
in a Mobile phone could provide a new dimension in the revolution of Mobile Phone. Covering these aspects, this
new system of wireless recharging will certainly bring innovative Change in recharging Electronic Equipment and
will upgrade our Lifestyle. Thus this paper successfully demonstrates a novel method of using the microwave’s
power to charge the Mobile Phones.