29-02-2016, 04:52 PM
Control Panel Buttons and Lights Tear Off (Pitch/Font) lights
Flash when continuous paper is in the tear-off position; otherwise, the lights indicate the selected font.
Feeds paper line by line when pressed and On when no paper is loaded in the selected paper released.
Ejects a single sheet or advances continuous paper to the next top-of- form position
when held down.
source or when paper is not loaded correctly. Flashes when paper has not been fully ejected
or a paper jam has occurred.
Pitch (Font) button
Selects a pitch and font.
Load/Eject button Loads a single sheet of paper.
Ejects a single sheet of paper if a sheet is loaded.
Loads continuous paper from the standby position.
Feeds continuous paper backwards to the standby position.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any use of this information as applied to other printers. Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and maintenance instructions. SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION. EPSON and EPSON ESC/P are registered trademarks and EPSON ESC/P2 is a trademark of SEIKO EPSON CORPORATION. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. IBM is a registered trademark of International Business Machines Corporation. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Pause button Stops printing temporarily, and resumes printing when pressed again. When pressed for three seconds, turns on the Micro Adjust mode*. To turn off, press again.Pause light On when the printer is paused.
*Micro Adjust mode
When you hold down the Pause button for three seconds, the printer enters the micro adjust mode. In this
mode, you can press the LF/FFD and Load/Eject U buttons to adjust the top-of-form or tear-off position. See Chapter 2, “Using the Printer.”
*Font select
In the Micro Adjust mode, you can select the font to use for printing by pressing the Tear Off button. The Tear Off lights turn on, off or flash to indicate the selected font.
Flashes when the printer is in the Micro Adjust mode*. Flashes when the print head has overheated
Flash when continuous paper is in the tear-off position; otherwise, the lights indicate the selected font.
Feeds paper line by line when pressed and On when no paper is loaded in the selected paper released.
Ejects a single sheet or advances continuous paper to the next top-of- form position
when held down.
source or when paper is not loaded correctly. Flashes when paper has not been fully ejected
or a paper jam has occurred.
Pitch (Font) button
Selects a pitch and font.
Load/Eject button Loads a single sheet of paper.
Ejects a single sheet of paper if a sheet is loaded.
Loads continuous paper from the standby position.
Feeds continuous paper backwards to the standby position.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any use of this information as applied to other printers. Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and maintenance instructions. SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION. EPSON and EPSON ESC/P are registered trademarks and EPSON ESC/P2 is a trademark of SEIKO EPSON CORPORATION. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. IBM is a registered trademark of International Business Machines Corporation. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Pause button Stops printing temporarily, and resumes printing when pressed again. When pressed for three seconds, turns on the Micro Adjust mode*. To turn off, press again.Pause light On when the printer is paused.
*Micro Adjust mode
When you hold down the Pause button for three seconds, the printer enters the micro adjust mode. In this
mode, you can press the LF/FFD and Load/Eject U buttons to adjust the top-of-form or tear-off position. See Chapter 2, “Using the Printer.”
*Font select
In the Micro Adjust mode, you can select the font to use for printing by pressing the Tear Off button. The Tear Off lights turn on, off or flash to indicate the selected font.
Flashes when the printer is in the Micro Adjust mode*. Flashes when the print head has overheated