30-07-2012, 11:06 AM
Cellphone-Based Device Control With Voice Acknowledgement
[attachment=29457]
Here is a circuit that lets you operate your home appliances like lights and water pump from your office or any other remote place. So if you forgot to switch off the lights or other appliances while going out, it helps you to turn off the appliance with your cellphone. Your cellphone works as the remote control for your home appliances. You can control the desired appliance by pressing the corresponding key. The system also gives you voice acknowledgement of the appliance status.
Circuit description
Fig.1 shows the circuit for cellphone based device control with voice acknowledgement. It comprises microcontroller AT89C51, DTMF decoder MT8870, voice recording/playback device APR9600 and a few discrete components. Microcontroller AT89C51 is at the heart of the circuit. It is a low-power, high-performance, 8-bit microcontroller with 4 kB of flash programmable and erasable read-only memory (PEROM) used as on-chip program memory, 128 bytes of RAM used as internal data memory, 32 individually programmable input/output (I/O) lines divided into four 8-bit ports, two 16-bit programmable timers/counters, a five-vector two-level interrupt architecture, on-chip oscillator and clock circuitry.
Recording and playback
To record the voice in IC2, follow Table III. Close SPST switch S19 to make pin 27 of IC2 low. Thereafter, press and hold switches S9 through S16 to record corresponding voice messages. LED2 flashes to indicate audio recording.
For playback of any device status, open SPST switch S19 and press the corresponding switch (S9 through S16). The recorded audio can be heard from the speaker connected to pins 14 and 15 of IC2. Fig.2 shows the pin configuration of mobile headset.
Software
The program (Device_Control.BAS) for the microcontroller is written using BASCOM microcontroller programming software. In the program, first, initialise the port (P0-P3) for corresponding controls. Thereafter, declare the variables for the program. After declaration, assign some initial value to variables. Here, microcontroller ports are initialised to make all the devices ‘off’ initially.
After that, the main function checks through ‘Do’ loop which control source has been enabled by using DIP switch pins. If you select switch S17, it searches the input from the mobile only. If you select switch S18, it searches the input from the switches (S1 through S8) only. If you enable both switch S17 and switch S18, it searches the inputs from switches and mobile. Else, the rest-status LED1 glows. Refer to Table II to select the control source.
[attachment=29457]
Here is a circuit that lets you operate your home appliances like lights and water pump from your office or any other remote place. So if you forgot to switch off the lights or other appliances while going out, it helps you to turn off the appliance with your cellphone. Your cellphone works as the remote control for your home appliances. You can control the desired appliance by pressing the corresponding key. The system also gives you voice acknowledgement of the appliance status.
Circuit description
Fig.1 shows the circuit for cellphone based device control with voice acknowledgement. It comprises microcontroller AT89C51, DTMF decoder MT8870, voice recording/playback device APR9600 and a few discrete components. Microcontroller AT89C51 is at the heart of the circuit. It is a low-power, high-performance, 8-bit microcontroller with 4 kB of flash programmable and erasable read-only memory (PEROM) used as on-chip program memory, 128 bytes of RAM used as internal data memory, 32 individually programmable input/output (I/O) lines divided into four 8-bit ports, two 16-bit programmable timers/counters, a five-vector two-level interrupt architecture, on-chip oscillator and clock circuitry.
Recording and playback
To record the voice in IC2, follow Table III. Close SPST switch S19 to make pin 27 of IC2 low. Thereafter, press and hold switches S9 through S16 to record corresponding voice messages. LED2 flashes to indicate audio recording.
For playback of any device status, open SPST switch S19 and press the corresponding switch (S9 through S16). The recorded audio can be heard from the speaker connected to pins 14 and 15 of IC2. Fig.2 shows the pin configuration of mobile headset.
Software
The program (Device_Control.BAS) for the microcontroller is written using BASCOM microcontroller programming software. In the program, first, initialise the port (P0-P3) for corresponding controls. Thereafter, declare the variables for the program. After declaration, assign some initial value to variables. Here, microcontroller ports are initialised to make all the devices ‘off’ initially.
After that, the main function checks through ‘Do’ loop which control source has been enabled by using DIP switch pins. If you select switch S17, it searches the input from the mobile only. If you select switch S18, it searches the input from the switches (S1 through S8) only. If you enable both switch S17 and switch S18, it searches the inputs from switches and mobile. Else, the rest-status LED1 glows. Refer to Table II to select the control source.