14-08-2012, 01:18 PM
Spartan-3E FPGA Starter Kit Board User Guide
[attachment=31461]
FPGA Configuration Options
The Spartan®-3E FPGA Starter Kit board supports a variety of FPGA configuration
options:
• Download FPGA designs directly to the Spartan-3E FPGA via JTAG, using the onboard
USB interface. The on-board USB-JTAG logic also provides in-system
programming for the on-board Platform Flash PROM and the Xilinx XC2C64A CPLD.
SPI serial Flash and StrataFlash programming are performed separately.
• Program the on-board 4 Mbit Xilinx XCF04S serial Platform Flash PROM, then
configure the FPGA from the image stored in the Platform Flash PROM using Master
Serial mode.
• Program the on-board 16 Mbit ST Microelectronics SPI serial Flash PROM, then
configure the FPGA from the image stored in the SPI serial Flash PROM using SPI
mode.
• Program the on-board 128 Mbit Intel StrataFlash parallel NOR Flash PROM, then
configure the FPGA from the image stored in the Flash PROM using BPI Up or BPI
Down configuration modes. Further, an FPGA application can dynamically load two
different FPGA configurations using the Spartan-3E FPGA’s MultiBoot mode. See the
Spartan-3E data sheet (DS312) for additional details on the MultiBoot feature.
Figure 4-1 indicates the position of the USB download/programming interface and the onboard
non-volatile memories that potentially store FPGA configuration images.Figure 4-2
provides additional details on configuration options.
PROG Push Button
The PROG push button, shown in Figure 4-2, page 26, forces the FPGA to reconfigure from
the selected configuration memory source. Press and release this button to restart the
FPGA configuration process at any time.
DONE Pin LED
The DONE pin LED, shown in Figure 4-2, page 26, lights whenever the FPGA is
successfully configured. If this LED is not lit, then the FPGA is not configured.
Programming Platform Flash PROM via USB
The on-board USB-JTAG circuitry also programs the Xilinx XCF04S serial Platform Flash
PROM. The steps provided in this section describe how to set up the PROM file and how
to download it to the board to ultimately program the FPGA.
Generating the FPGA Configuration Bitstream File
Before generating the PROM file, create the FPGA bitstream file. The FPGA provides an
output clock, CCLK, when loading itself from an external PROM. The FPGA’s internal
CCLK oscillator always starts at its slowest setting, approximately 1.5 MHz. Most external
PROMs support a higher frequency. Increase the CCLK frequency as appropriate to reduce
the FPGA’s configuration time. The Xilinx XCF04S Platform Flash supports a 25 MHz
CCLK frequency.
[attachment=31461]
FPGA Configuration Options
The Spartan®-3E FPGA Starter Kit board supports a variety of FPGA configuration
options:
• Download FPGA designs directly to the Spartan-3E FPGA via JTAG, using the onboard
USB interface. The on-board USB-JTAG logic also provides in-system
programming for the on-board Platform Flash PROM and the Xilinx XC2C64A CPLD.
SPI serial Flash and StrataFlash programming are performed separately.
• Program the on-board 4 Mbit Xilinx XCF04S serial Platform Flash PROM, then
configure the FPGA from the image stored in the Platform Flash PROM using Master
Serial mode.
• Program the on-board 16 Mbit ST Microelectronics SPI serial Flash PROM, then
configure the FPGA from the image stored in the SPI serial Flash PROM using SPI
mode.
• Program the on-board 128 Mbit Intel StrataFlash parallel NOR Flash PROM, then
configure the FPGA from the image stored in the Flash PROM using BPI Up or BPI
Down configuration modes. Further, an FPGA application can dynamically load two
different FPGA configurations using the Spartan-3E FPGA’s MultiBoot mode. See the
Spartan-3E data sheet (DS312) for additional details on the MultiBoot feature.
Figure 4-1 indicates the position of the USB download/programming interface and the onboard
non-volatile memories that potentially store FPGA configuration images.Figure 4-2
provides additional details on configuration options.
PROG Push Button
The PROG push button, shown in Figure 4-2, page 26, forces the FPGA to reconfigure from
the selected configuration memory source. Press and release this button to restart the
FPGA configuration process at any time.
DONE Pin LED
The DONE pin LED, shown in Figure 4-2, page 26, lights whenever the FPGA is
successfully configured. If this LED is not lit, then the FPGA is not configured.
Programming Platform Flash PROM via USB
The on-board USB-JTAG circuitry also programs the Xilinx XCF04S serial Platform Flash
PROM. The steps provided in this section describe how to set up the PROM file and how
to download it to the board to ultimately program the FPGA.
Generating the FPGA Configuration Bitstream File
Before generating the PROM file, create the FPGA bitstream file. The FPGA provides an
output clock, CCLK, when loading itself from an external PROM. The FPGA’s internal
CCLK oscillator always starts at its slowest setting, approximately 1.5 MHz. Most external
PROMs support a higher frequency. Increase the CCLK frequency as appropriate to reduce
the FPGA’s configuration time. The Xilinx XCF04S Platform Flash supports a 25 MHz
CCLK frequency.