27-02-2013, 09:58 AM
WiMAX REPORT
[attachment=51992]
INTRODUCTION
What if there were a new technology that solved all of these problems? This new technology would provide:
• The high speed of broadband service
• Wireless rather than wired access, so it would be a lot less expensive than cable or DSL and much easier to extend to suburban and rural areas
• Broad coverage like the cell phone network instead of small WiFi hotspots
This system is actually coming into being right now, and it is called WiMAX. WiMAX is short for Worldwide Interoperability for Microwave Access, and it also goes by the IEEE name 802.16.
WiMAX has the potential to do to broadband Internet access what cell phones have done to phone access. In the same way that many people have given up their "land lines" in favor of cell phones, WiMAX could replace cable and DSL services, providing universal Internet access just about anywhere you go. WiMAX will also be as painless as WiFi -- turning your computer on will automatically connect you to the closest available WiMAX antenna.
In this article, we'll find out how WiMAX works, what engineers are doing to make it better and what it could mean for the future of wireless Internet
In practical terms, WiMAX would operate similar to WiFi but at higher speeds, over greater distances and for a greater number of users. WiMAX could potentially erase the suburban and rural blackout areas that currently have no broadband Internet access because phone and cable companies have not yet run the necessary wires to those remote locations.
What Can WiMAX Do?
WiMAX operates on the same general principles as WiFi -- it sends data from one computer to another via radio signals. A computer (either a desktop or a laptop) equipped with WiMAX would receive data from the WiMAX transmitting station, probably using encrypted data keys to prevent unauthorized users from stealing access.
The fastest WiFi connection can transmit up to 54 megabits per second under optimal conditions. WiMAX should be able to handle up to 70 megabits per second. Even once that 70 megabits is split up between several dozen businesses or a few hundred home users, it will provide at least the equivalent of cable-modem transfer rates to each user.
The WiMAX Scenario
Here's what would happen if you got WiMAX. An Internet service provider sets up a WiMAX base station 10 miles from your home. You would buy a WiMAX-enabled computer (some of them should be on store shelves in 2005) or upgrade your old computer to add WiMAX capability. You would receive a special encryption code that would give you access to the base station. The base station would beam data from the Internet to your computer (at speeds potentially higher than today's cable modems), for which you would pay the provider a monthly fee. The cost for this service could be much lower than current high-speed Internet-subscription fees because the provider never had to run cables.
WiFi Hotspots
If you want to take advantage of public WiFi hotspots or start a wireless network in your home, the first thing you'll need to do is make sure your computer has the right wireless gear. Most new laptops and many new desktop computers come with built-in wireless transmitters. If your laptop doesn't, you can buy a wireless adapter that plugs into the PC card slot or USB port. Desktop computers can use USB adapters, or you can buy an adapter that plugs into the PCI slot inside the computer's case. Many of these adapters can use more than one 802.11 standard.
Once you've installed your wireless adapter and the drivers that allow it to operate, your computer should be able to automatically discover existing networks. This means that when you turn your computer on in a WiFi hotspot, the computer will inform you that the network exists and ask whether you want to connect to it. If you have an older computer, you may need to use a software program to detect and connect to a wireless network.
Being able to connect to the Internet in public hotspots is extremely convenient. Wireless home networks are convenient as well. They allow you to easily connect multiple computers and to move them from place to place without disconnecting and reconnecting wires. In the next section, we'll look at how to create a wireless network in your home.
Building a Wireless Network
If you already have several computers networked in your home, you can create a wireless network with a wireless access point. If you have several computers that are not networked, or if you want to replace your Ethernet network, you'll need a wireless router. This is a single unit that contains:
1. A port to connect to your cable or DSL modem
2. A router
3. An Ethernet hub
4. A firewall
5. A wireless access point
A wireless router allows you to use wireless signals or Ethernet cables to connect your computers to one another, to a printer and to the Internet. Most routers provide coverage for about 100 feet (30.5 meters) in all directions, although walls and doors can block the signal. If your home is very large, you can buy inexpensive range extenders or repeaters to increase your router's range.
Wireless Application Protocol
Here's what happens when you access a Web site using a WAP-enabled device:
• You turn on the device and open the minibrowser.
• The device sends out a radio signal, searching for service.
• A connection is made with your service provider.
• You select a Web site that you wish to view.
• A request is sent to a gateway server using WAP.
• The gateway server retrieves the information via HTTP from the Web site.
• The gateway server encodes the HTTP data as WML.
• The WML-encoded data is sent to your device.
• You see the wireless Internet version of the Web page you selected.
To create wireless Internet content, a Web site creates special text-only or low-graphics versions of the site. The data is sent in HTTP form by a Web server to a WAP gateway. This system includes the WAP encoder, script compiler and protocol adapters to convert the HTTP information to WML. The gateway then sends the converted data to the WAP client on your wireless device.
[attachment=51992]
INTRODUCTION
What if there were a new technology that solved all of these problems? This new technology would provide:
• The high speed of broadband service
• Wireless rather than wired access, so it would be a lot less expensive than cable or DSL and much easier to extend to suburban and rural areas
• Broad coverage like the cell phone network instead of small WiFi hotspots
This system is actually coming into being right now, and it is called WiMAX. WiMAX is short for Worldwide Interoperability for Microwave Access, and it also goes by the IEEE name 802.16.
WiMAX has the potential to do to broadband Internet access what cell phones have done to phone access. In the same way that many people have given up their "land lines" in favor of cell phones, WiMAX could replace cable and DSL services, providing universal Internet access just about anywhere you go. WiMAX will also be as painless as WiFi -- turning your computer on will automatically connect you to the closest available WiMAX antenna.
In this article, we'll find out how WiMAX works, what engineers are doing to make it better and what it could mean for the future of wireless Internet
In practical terms, WiMAX would operate similar to WiFi but at higher speeds, over greater distances and for a greater number of users. WiMAX could potentially erase the suburban and rural blackout areas that currently have no broadband Internet access because phone and cable companies have not yet run the necessary wires to those remote locations.
What Can WiMAX Do?
WiMAX operates on the same general principles as WiFi -- it sends data from one computer to another via radio signals. A computer (either a desktop or a laptop) equipped with WiMAX would receive data from the WiMAX transmitting station, probably using encrypted data keys to prevent unauthorized users from stealing access.
The fastest WiFi connection can transmit up to 54 megabits per second under optimal conditions. WiMAX should be able to handle up to 70 megabits per second. Even once that 70 megabits is split up between several dozen businesses or a few hundred home users, it will provide at least the equivalent of cable-modem transfer rates to each user.
The WiMAX Scenario
Here's what would happen if you got WiMAX. An Internet service provider sets up a WiMAX base station 10 miles from your home. You would buy a WiMAX-enabled computer (some of them should be on store shelves in 2005) or upgrade your old computer to add WiMAX capability. You would receive a special encryption code that would give you access to the base station. The base station would beam data from the Internet to your computer (at speeds potentially higher than today's cable modems), for which you would pay the provider a monthly fee. The cost for this service could be much lower than current high-speed Internet-subscription fees because the provider never had to run cables.
WiFi Hotspots
If you want to take advantage of public WiFi hotspots or start a wireless network in your home, the first thing you'll need to do is make sure your computer has the right wireless gear. Most new laptops and many new desktop computers come with built-in wireless transmitters. If your laptop doesn't, you can buy a wireless adapter that plugs into the PC card slot or USB port. Desktop computers can use USB adapters, or you can buy an adapter that plugs into the PCI slot inside the computer's case. Many of these adapters can use more than one 802.11 standard.
Once you've installed your wireless adapter and the drivers that allow it to operate, your computer should be able to automatically discover existing networks. This means that when you turn your computer on in a WiFi hotspot, the computer will inform you that the network exists and ask whether you want to connect to it. If you have an older computer, you may need to use a software program to detect and connect to a wireless network.
Being able to connect to the Internet in public hotspots is extremely convenient. Wireless home networks are convenient as well. They allow you to easily connect multiple computers and to move them from place to place without disconnecting and reconnecting wires. In the next section, we'll look at how to create a wireless network in your home.
Building a Wireless Network
If you already have several computers networked in your home, you can create a wireless network with a wireless access point. If you have several computers that are not networked, or if you want to replace your Ethernet network, you'll need a wireless router. This is a single unit that contains:
1. A port to connect to your cable or DSL modem
2. A router
3. An Ethernet hub
4. A firewall
5. A wireless access point
A wireless router allows you to use wireless signals or Ethernet cables to connect your computers to one another, to a printer and to the Internet. Most routers provide coverage for about 100 feet (30.5 meters) in all directions, although walls and doors can block the signal. If your home is very large, you can buy inexpensive range extenders or repeaters to increase your router's range.
Wireless Application Protocol
Here's what happens when you access a Web site using a WAP-enabled device:
• You turn on the device and open the minibrowser.
• The device sends out a radio signal, searching for service.
• A connection is made with your service provider.
• You select a Web site that you wish to view.
• A request is sent to a gateway server using WAP.
• The gateway server retrieves the information via HTTP from the Web site.
• The gateway server encodes the HTTP data as WML.
• The WML-encoded data is sent to your device.
• You see the wireless Internet version of the Web page you selected.
To create wireless Internet content, a Web site creates special text-only or low-graphics versions of the site. The data is sent in HTTP form by a Web server to a WAP gateway. This system includes the WAP encoder, script compiler and protocol adapters to convert the HTTP information to WML. The gateway then sends the converted data to the WAP client on your wireless device.