02-03-2013, 02:38 PM
BLUE TOOTH
[attachment=52430]
INTRODUCTION
Blue tooth operates in the unlicensed ISM band at 2.4 GHZ frequency band and use frequency hopping spread spectrum technique. A typical Blue tooth device has a range of about 10 meters and can be extended to 100meters. Communication channels supports total bandwidth of 1 Mb / sec. A single connection supports a maximum asymmetric data transfer rate of 721 KBPS maximum of three channels.
BLUE TOOTH - NETWORKS
In bluetooth, a Piconet is a collection of up to 8 devices that frequency hop together. Each Piconet has one master usually a device that initiated establishment of the Piconet, and up to 7 slave devices. Master's Blue tooth address is used for definition of the frequency hopping sequence. Slave devices use the master's clock to synchronize their clocks to be able to hop simultaneously.
A Piconet
When a device wants to establish a Piconet it has to perform inquiry to discover other Blue tooth devices in the range. Inquiry procedure is defined in such a way to ensure that two devices will after some time, visit the same frequency same time when that happens, required information is exchanged and devices can use paging procedure to establish connection.When more than 7 devices needs to communicate, there are two options. The first one is to put one or more devices into the park state. Blue tooth defines three low power modes sniff, hold and park. When a device is in the park mode then it disassociates from and Piconet, but still maintains timing synchronization with it. The master of the Piconet periodically broadcasts beacons (Warning) to invite the slave to rejoin the Piconet or to allow the slave to request to rejoin. The slave can rejoin the Piconet only if there are less than seven slaves already in the Piconet. If not so, the master has to 'park' one of the active slaves first.
All these actions cause delay and for some applications it can be unacceptable for eg: process control applications, that requires immediate response from the command centre (central control room).Scatternet consists of several Piconets connected by devices participating in multiple Piconet. These devices can be slaves in all Piconets or master in one Piconet and slave in other Piconets. Using scatternets higher throughput is available and multi-hop connections between devices in different Piconets are possible. i.e., The unit can communicate in one Piconet at time so they jump from pioneer to another depending upon the channel parameter.
[attachment=52430]
INTRODUCTION
Blue tooth operates in the unlicensed ISM band at 2.4 GHZ frequency band and use frequency hopping spread spectrum technique. A typical Blue tooth device has a range of about 10 meters and can be extended to 100meters. Communication channels supports total bandwidth of 1 Mb / sec. A single connection supports a maximum asymmetric data transfer rate of 721 KBPS maximum of three channels.
BLUE TOOTH - NETWORKS
In bluetooth, a Piconet is a collection of up to 8 devices that frequency hop together. Each Piconet has one master usually a device that initiated establishment of the Piconet, and up to 7 slave devices. Master's Blue tooth address is used for definition of the frequency hopping sequence. Slave devices use the master's clock to synchronize their clocks to be able to hop simultaneously.
A Piconet
When a device wants to establish a Piconet it has to perform inquiry to discover other Blue tooth devices in the range. Inquiry procedure is defined in such a way to ensure that two devices will after some time, visit the same frequency same time when that happens, required information is exchanged and devices can use paging procedure to establish connection.When more than 7 devices needs to communicate, there are two options. The first one is to put one or more devices into the park state. Blue tooth defines three low power modes sniff, hold and park. When a device is in the park mode then it disassociates from and Piconet, but still maintains timing synchronization with it. The master of the Piconet periodically broadcasts beacons (Warning) to invite the slave to rejoin the Piconet or to allow the slave to request to rejoin. The slave can rejoin the Piconet only if there are less than seven slaves already in the Piconet. If not so, the master has to 'park' one of the active slaves first.
All these actions cause delay and for some applications it can be unacceptable for eg: process control applications, that requires immediate response from the command centre (central control room).Scatternet consists of several Piconets connected by devices participating in multiple Piconet. These devices can be slaves in all Piconets or master in one Piconet and slave in other Piconets. Using scatternets higher throughput is available and multi-hop connections between devices in different Piconets are possible. i.e., The unit can communicate in one Piconet at time so they jump from pioneer to another depending upon the channel parameter.