05-04-2011, 12:32 PM
Main Project report 2008[1].doc (Size: 387.5 KB / Downloads: 318)
NAME OF THE PROJECT (bold Capital 18)
A Project Report ( bold 16)
Submitted by (12)
Name of student 1 ( bold 14)
Name of student 2(bold 14)
Name of student 3((bold 14)
Name of student 4(bold 14)
In partial fulfillment of the requirements for award of the degree of (12) Bachelor of Technology (bold 14) in (12) Electronics & Instrumentation Engineering (14)
(bold capital 14)
FEDERAL INSTITUTE OF SCIENCE AND TECHNOLOGY (FISAT)
Angamaly-683577, Ernakulam
Affiliated to (12)
MAHATMA GANDHI UNIVERSITY (BOLD capital 14)
Kottayam-686560(12)
May 2008 (bold 14)
NAME OF THE PROJECT (bold Capital 18)
A Project Report (bold 16)
Submitted by (12)
Name of student 1 ( bold 14)
Name of student 2(bold 14)
Name of student 3((bold 14)
Name of student 4(bold 14)
In partial fulfillment of the requirements for award of the degree of (12) Bachelor of Technology (bold 14) in (12) Electronics & Instrumentation Engineering (14)
(bold capital 14)
FEDERAL INSTITUTE OF SCIENCE AND TECHNOLOGY (FISAT)
Angamaly-683577, Ernakulam
Affiliated to (12)
MAHATMA GANDHI UNIVERSITY (BOLD capital 14)
Kottayam-686560(12)
May 2008 (bold 14)
FEDERAL INSTITUTE OF SCIENCE AND TECHNOLOGY (FISAT) (bold capital 14)
Mookkannoor(p.o), Angamaly-683577(14)
CERTIFICATE (bold capital 14)
This is to certify that the project report titled (14) Name of the project (bold 14) submitted by Name of the student , towards partial fulfillment of the requirements for the award of the degree of Bachelor of Technology in Electronics and Instrumentation Engineering is a record of bonafide work carried out by them during the academic year 2007 –2008(14)
Internal Guide (14) Head of the Department (14)
Name Smitha.I.S
Designation Asst. professor
Department of EIE Department of EIE
FISAT FISAT
Place:
Date:
Note:
Place a white transparent sheet before the first page of the report
Place a white transparent sheet before the certificate
Second page - Certificate from industry
Place a white transparent sheet .
Next page – certificate from college.
Third page –Acknowledgement (one page)
Fourth page – Abstract (one page) (Italics)
Fifth page – Contents (Maximum of 2 pages)
Sixth page -list of symbols and abbreviations used (if any)
CONTENTS (bold capital 16)
Chapter 1 INTRODUCTION (bold capital 14) Page Number
It includes introduction to your project. To be restricted to one page
Chapter 2 TITLE OF CHAPTER (bold capital 14)
Enter the sub divisions as 2.1(12)
2.1.1
2.1.2
2.2 etc
All the figures, tables etc must be numbered.
The figure number and caption should appear below the figure.
The table number and caption should appear above the table.
Chapter 3 etc
Chapter N -1 (Results if any)
Chapter N CONCLUSION
References (In IEEE Format)
[1] W.Ding and B.Liu, “Rate control of MPEG video coding and recording by rate quantization modeling”, IEEE trans.on circuits and systems for video technology,vol.6,pp.12-20,Feb.1996
[2] --------------
All references to the above should be indicated as
( eg) According to Ding[1]
(Please refer IEEE transactions in the Library)
Appendix (Includes Data sheet, tables, programs, photographs etc if any)
Place a title page before every chapter.
The report shall be made with good quality bond paper.
Note: The format of the inner pages is attached…..