15-05-2012, 12:41 PM
Power semiconductor device
Power semiconductor device.docx (Size: 290.17 KB / Downloads: 37)
Power semiconductor devices are semiconductor devices used as switches or rectifiers in power electronic circuits (switch mode power supplies for example). They are also called power devices or when used in integrated circuits, called power ICs.
Most power semiconductor devices are only used in "commutation mode" (i.e. they are either on or off), and are therefore optimized for this. Most of them should not be used in linear operation.
History
Power semiconductor devices first appeared in 1952 with the introduction of the power diode by R.N. Hall. It was made of Germanium and had a voltage capability of 200 volts and a current rating of 35 amperes.
The thyristor appeared in 1957. Thyristors are able to withstand very high reverse breakdown voltage and are also capable of carrying high current. One disadvantage of the thyristor for switching circuits is that once it is 'latched-on' in the conducting state it cannot be turned off by external control. The thyristor turn-off is passive, i.e., the power must be disconnected from the device.
The first bipolar transistors devices with substantial power handling capabilities were introduced in the 1960s. These components overcame some limitations of the thyristors because they can be turned on or off with an applied signal.
With the improvements of the Metal Oxide Semiconductor technology (initially developed to produce integrated circuits), power MOSFETs became available in the late 1970s. International Rectifier introduced a 25 A, 400 V power MOSFET in 1978.[1] These devices allow operation at higher frequency than bipolar transistors, but are limited to the low voltage applications.
The Insulated Gate Bipolar Transistor (IGBT) developed in the 1980s became widely available in the 1990s. This component has the power handling capability of the bipolar transistor, with the advantages of the isolated gate drive of the power MOSFET.
Common power devices
Some common power devices are the power diode, thyristor, power MOSFET and IGBT. A power diode or MOSFET operates on similar principles to its low-power counterpart, but is able to carry a larger amount of current and typically is able to support a larger reverse-bias voltage in the off-state.
Structural changes are often made in power devices to accommodate the higher current density, higher power dissipation and/or higher reverse breakdown voltage. The vast majority of the discrete (i.e. non integrated) power devices are built using a vertical structure, whereas small-signal devices employ a lateral structure. With the vertical structure, the current rating of the device is proportional to its area, and the voltage blocking capability is achieved in the height of the die. With this structure, one of the connections of the device is located on the bottom of the semiconductor die.
Common power semiconductor devices
• The two-terminal devices (diodes), whose state is completely dependent on the external power circuit they are connected to;
• The three-terminal devices, whose state is not only dependent on their external power circuit, but also on the signal on their driving terminal (gate or base). Transistors and thyristors belong to that category.
A second classification is less obvious, but has a strong influence on device performance: Some devices are majority carrier devices (Schottky diode, MOSFET), while the others are minority carrier devices (Thyristor, bipolar transistor, IGBT). The former use only one type of charge carriers, while the latter use both (i.e. electrons and holes). The majority carrier devices are faster, but the charge injection of minority carrier devices allows for better On-state performance.
Diodes
An ideal diode should have the following characteristics:
• When forward-biased, the voltage across the end terminals of the diode should be zero, whatever the current that flows through it (on-state);
• When reverse-biased, the leakage current should be zero, whatever the voltage (off-state).
• The transition between on and off states should be instantaneous.
In reality, the design of a diode is a trade-off between performance in on-state, off-state and commutation. Indeed, the same area of the device must sustain the blocking voltage in the off-state and allow current flow in the on-state. As the requirements for the two states are completely opposite, a diode has to be either optimised for one of them, or time must be allowed to switch from one state to the other (i.e. slow down the commutation speed).
This trade-off between on-state/off-state and switching speed is the same for all power devices. A Schottky diode has excellent switching speed and on-state performance, but a high level of leakage current in off-state. On the other hand, PIN diodes are commercially available in different commutation speeds (so-called "fast" and "ultrafast" rectifiers), but any increase in speed is paid for by a lower performance in the on-state.
Switches
The trade-off between voltage, current and frequency ratings also exists for the switches. Actually, all power semiconductors rely on a PIN diode structure to sustain voltage. This can be seen in figure 2. The power MOSFET has the advantages of the majority carrier devices, so it can achieve very high operating frequency, but can't be used with high voltages. As it is a physical limit, no improvement is expected from silicon MOSFETs concerning their maximum voltage ratings. However, its excellent performance in low voltage make it the device of choice (actually the only choice) for applications below 200 V. By paralleling several devices, it is possible to increase the current rating of a switch. The MOSFET is particularly suited to this configuration because its positive thermal coefficient of resistance tends to balance current between individual devices.
Power semiconductor device.docx (Size: 290.17 KB / Downloads: 37)
Power semiconductor devices are semiconductor devices used as switches or rectifiers in power electronic circuits (switch mode power supplies for example). They are also called power devices or when used in integrated circuits, called power ICs.
Most power semiconductor devices are only used in "commutation mode" (i.e. they are either on or off), and are therefore optimized for this. Most of them should not be used in linear operation.
History
Power semiconductor devices first appeared in 1952 with the introduction of the power diode by R.N. Hall. It was made of Germanium and had a voltage capability of 200 volts and a current rating of 35 amperes.
The thyristor appeared in 1957. Thyristors are able to withstand very high reverse breakdown voltage and are also capable of carrying high current. One disadvantage of the thyristor for switching circuits is that once it is 'latched-on' in the conducting state it cannot be turned off by external control. The thyristor turn-off is passive, i.e., the power must be disconnected from the device.
The first bipolar transistors devices with substantial power handling capabilities were introduced in the 1960s. These components overcame some limitations of the thyristors because they can be turned on or off with an applied signal.
With the improvements of the Metal Oxide Semiconductor technology (initially developed to produce integrated circuits), power MOSFETs became available in the late 1970s. International Rectifier introduced a 25 A, 400 V power MOSFET in 1978.[1] These devices allow operation at higher frequency than bipolar transistors, but are limited to the low voltage applications.
The Insulated Gate Bipolar Transistor (IGBT) developed in the 1980s became widely available in the 1990s. This component has the power handling capability of the bipolar transistor, with the advantages of the isolated gate drive of the power MOSFET.
Common power devices
Some common power devices are the power diode, thyristor, power MOSFET and IGBT. A power diode or MOSFET operates on similar principles to its low-power counterpart, but is able to carry a larger amount of current and typically is able to support a larger reverse-bias voltage in the off-state.
Structural changes are often made in power devices to accommodate the higher current density, higher power dissipation and/or higher reverse breakdown voltage. The vast majority of the discrete (i.e. non integrated) power devices are built using a vertical structure, whereas small-signal devices employ a lateral structure. With the vertical structure, the current rating of the device is proportional to its area, and the voltage blocking capability is achieved in the height of the die. With this structure, one of the connections of the device is located on the bottom of the semiconductor die.
Common power semiconductor devices
• The two-terminal devices (diodes), whose state is completely dependent on the external power circuit they are connected to;
• The three-terminal devices, whose state is not only dependent on their external power circuit, but also on the signal on their driving terminal (gate or base). Transistors and thyristors belong to that category.
A second classification is less obvious, but has a strong influence on device performance: Some devices are majority carrier devices (Schottky diode, MOSFET), while the others are minority carrier devices (Thyristor, bipolar transistor, IGBT). The former use only one type of charge carriers, while the latter use both (i.e. electrons and holes). The majority carrier devices are faster, but the charge injection of minority carrier devices allows for better On-state performance.
Diodes
An ideal diode should have the following characteristics:
• When forward-biased, the voltage across the end terminals of the diode should be zero, whatever the current that flows through it (on-state);
• When reverse-biased, the leakage current should be zero, whatever the voltage (off-state).
• The transition between on and off states should be instantaneous.
In reality, the design of a diode is a trade-off between performance in on-state, off-state and commutation. Indeed, the same area of the device must sustain the blocking voltage in the off-state and allow current flow in the on-state. As the requirements for the two states are completely opposite, a diode has to be either optimised for one of them, or time must be allowed to switch from one state to the other (i.e. slow down the commutation speed).
This trade-off between on-state/off-state and switching speed is the same for all power devices. A Schottky diode has excellent switching speed and on-state performance, but a high level of leakage current in off-state. On the other hand, PIN diodes are commercially available in different commutation speeds (so-called "fast" and "ultrafast" rectifiers), but any increase in speed is paid for by a lower performance in the on-state.
Switches
The trade-off between voltage, current and frequency ratings also exists for the switches. Actually, all power semiconductors rely on a PIN diode structure to sustain voltage. This can be seen in figure 2. The power MOSFET has the advantages of the majority carrier devices, so it can achieve very high operating frequency, but can't be used with high voltages. As it is a physical limit, no improvement is expected from silicon MOSFETs concerning their maximum voltage ratings. However, its excellent performance in low voltage make it the device of choice (actually the only choice) for applications below 200 V. By paralleling several devices, it is possible to increase the current rating of a switch. The MOSFET is particularly suited to this configuration because its positive thermal coefficient of resistance tends to balance current between individual devices.